|
宏宇广告标识有限公司 
| 联系人：黄成南 先生 (销售) |
 |
| 电 话：021-56388008 |
|
| 手 机：13816089387 |
|
 |
|
 |
|
 |
|
| 供应3M180C-10 |
Controltac™ Plus
Graphic Film with Comply Performance Series 180C
For Screen Printing Only
Description
3M™ Controltac™ Plus Graphic Film with Comply™ Performance Series 180 is a versatile, removable, 2 mil film with a positionable, pressure activated adhesive to make handling large format graphics easier. It also has Comply performance for easier, high quality installations. This film can be used on flat and corrugated with rivet surfaces.
Advantages
• Screen printable
• Wide color selection
• Lifetime warranty for trailers;
up to 7 years for other applications
• Easy to temporarily position during application
• Removable with heat or a chemical system
Application and End Uses
Film series 180C is intended for making removable, durable graphics when used with the listed Compatible Products in the following applications. These types of applications are warranted by the 3M™ MCS™ Warranty with the Special Warranty Stipulations when used for automobile or vehicle graphics. See page 5.
• Interior and exterior graphics and signs
• Commercial vehicle and fleet graphics, emblems or striping
• Bus graphics
Limitations of End Uses
We do not normally warrant other applications, but please contact us to discuss your needs or let us suggest other 3M products.
Specifically, we do not warrant this film for the following:
• Graphics applied to:
- Stainless steel.
- Non-3M films (also see Removal on page 7).
- Substrates that do not have a clean, smooth surface.
• Graphic removal from:
- Applications with poor paint-to-substrate adhesion.
- Existing graphics that must remain intact. Damage may occur during removal of film series 180C.
• Graphics subjected to:
- Gasoline vapors or spills at gas pumps, automobile fuel-tank ports, or top-feeding, petroleum tankers.
• Graphics made for automotive Original Equipment Manufacturers (OEM); contact 3M Automotive Division at 1-800-328-1684, Ext. 444, for alternatives.
NOTE: Film used on buses must not be applied so as to restrict the safe use of emergency window exits. See Instruction Bulletin 5.4, Release G, July 2003 or later for details.
Compatible Products
• 3M™ Screen Printing Ink Series 1900 (line & 4-color)
• 3M™ Screen Printing Ink Series 9700UV (line & 4-color)
• 3M™ Edge Sealer 3950
• 3M™ Prespacing Tape SCPS-2 and SPCS-53X
• 3M™ Premasking Tape SCPM-3 and SCPM-44X
Characteristics
Characteristic Description
Film Cast vinyl
Thickness 2 mils (0.05 mm) without adhesive
3-4 mils (0.08-0.10 mm) with adhesive
Color See the Color Chart on page 2.
Adhesive type Positionable, pressure activated with Comply performance feature
Adhesive color Films with * in color chart: Clear
All other films: Gray-pigmented
Liner Polyethylene-coated layflat paper
Application surface Flat, with and without rivets; corrugated; simple curves,; moderate compound curves
Application substrates ABS resins, aluminum, chrome, glass, fiberglass reinforced plastics, paint (check adhesion to powder-coated or water-based paints)
Application temperature range Flat surfaces with and without rivets: 40 to 100F (4 to 38C)
Corrugated surfaces with rivets:
50 to 100F (10 to 38C)
Removal Removable with heat or chemicals within 7 years
Removal temperature 50 F (10C) minimum
(air and substrate) |
 |
| |
|
|
 |
|
|
免责声明： 以上所展示的信息由会员自行提供，内容的真实性、准确性和合法性由发布会员负责，企业录对此不承担任何责任。如有侵犯您的权益，请来信通知删除。